Keyword: alignment
Paper Title Other Keywords Page
MOPA12 Commissioning of HOM Detectors in the First Cryomodule of the LCLS-II Linac HOM, cavity, MMI, cryomodule 69
 
  • J.A. Diaz Cruz
    UNM-ECE, Albuquerque, USA
  • B.T. Jacobson, N.R. Neveu, J.P. Sikora
    SLAC, Menlo Park, California, USA
 
  Long-range wakefields (LRWs) may cause emittance dilution effects. LWRs are especially unwanted at facilities with low emittance beams like the LCLS-II at SLAC. Dipolar higher-order modes (HOMs) are a set of LRWs that are excited by off-axis beams. Two 4-channel HOM detectors were built to measure the beam-induced HOM signals for TESLA-type superconducting RF (SRF) cavities; they were tested at the Fermilab Accelerator Science and Technology (FAST) facility and are now installed at SLAC. The HOM detectors were designed to investigate LRW effects on the beam and to help with beam alignment. This paper presents preliminary results of HOM measurements at the first cryomodule (CM01) of the LCLS-II linac and describes the relevant hardware and setup of the experiment.  
DOI • reference for this paper ※ doi:10.18429/JACoW-NAPAC2022-MOPA12  
About • Received ※ 09 August 2022 — Accepted ※ 20 August 2022 — Issue date ※ 31 August 2022  
Cite • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
TUPA02 Characterization of Octupole Elements for IOTA multipole, octupole, dipole, optics 351
 
  • J.N. Wieland
    MSU, East Lansing, Michigan, USA
  • J.D. Jarvis, A.L. Romanov, A. Valishev
    Fermilab, Batavia, Illinois, USA
 
  Funding: Work partially supported by the US Department of Energy, Office of Science, High Energy Physics under Cooperative Agreement award number DE-SC0018362 and Michigan State University.
The Integrable Optics Test Accelerator (IOTA) is a research storage ring constructed and operated at Fermilab to demonstrate the advantages of nonlinear integrable lattices. One of the nonlinear lattice configurations with one integral of motion is based on a string of short octupoles. The results of the individual magnet’s characterizations, which were necessary to determine their multipole composition and magnetic centers, are presented. This information was used to select and align the best subset of octupoles for the IOTA run 4.
 
DOI • reference for this paper ※ doi:10.18429/JACoW-NAPAC2022-TUPA02  
About • Received ※ 03 August 2022 — Revised ※ 08 August 2022 — Accepted ※ 09 August 2022 — Issue date ※ 08 September 2022
Cite • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
TUPA17 Beam-Based Alignment of Sextupole Families in the EIC sextupole, kicker, lattice, closed-orbit 378
 
  • J.C. Wang, G.H. Hoffstaetter, D. Sagan
    Cornell University (CLASSE), Cornell Laboratory for Accelerator-Based Sciences and Education, Ithaca, New York, USA
  • C. Montag
    BNL, Upton, New York, USA
 
  To steer the closed orbit in a storage ring through the center of its quadrupoles, it is important to accurately know the quadrupole centers relative to nearby beam position monitors. Usually this is achieved by beam-based alignment (BBA). Assuming the quadrupole strength can be changed individually, one finds the BPM reading where changing a quadrupole’s strength does not alter the closed orbit. Since most quadrupoles are powered in series, they can only be varied independently if costly power supplies are added. For the EIC electron storage ring (ESR), we investigate whether sextupole BBA can be used instead. Individually powered sextupole BBA techniques already exist, but most sextupoles are powered in families and cannot be individually changed. We therefore developed a method where a localized bump changes the beam excursion in a single sextupole of a family, turning off all families that also have sextupoles in the bump. The bump amplitude at which the sextupole does not cause a closed orbit kick determines the sextupole’s alignment. This study was made to investigate the precision to which this method can be utilized.  
DOI • reference for this paper ※ doi:10.18429/JACoW-NAPAC2022-TUPA17  
About • Received ※ 04 August 2022 — Revised ※ 08 August 2022 — Accepted ※ 10 August 2022 — Issue date ※ 29 August 2022
Cite • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
TUPA48 Effect of Lattice Misalignments on Beam Dynamics in LANSCE Linear Accelerator emittance, linac, lattice, simulation 455
 
  • Y.K. Batygin, S.S. Kurennoy
    LANL, Los Alamos, New Mexico, USA
 
  Funding: Work supported by US DOE under contract 89233218CNA000001
Accelerator channel misalignments can significantly affect beam parameters in long linear accelerators. Measurements of misalignments of the LANSCE linac lattice elements was performed by the Mechanical Design Engineering Group of the Los Alamos Accelerator Operations and Technology Division. In order to determine effect of misalignment on beam parameters in LANSCE linac, the start-to-end simulations of LANSCE accelerator were performed using Beampath and CST codes including measured displacements of quadrupoles and accelerating tanks. Simulations were done for both H+ and H beams with various beam flavors. Effect of misalignments was compared with those due to beam space charge and distortion of RF field along the channel. Paper presents results of simulation and comparison with experimental data of beam emittance growth along the machine.
 
poster icon Poster TUPA48 [1.547 MB]  
DOI • reference for this paper ※ doi:10.18429/JACoW-NAPAC2022-TUPA48  
About • Received ※ 23 July 2022 — Revised ※ 28 July 2022 — Accepted ※ 04 August 2022 — Issue date ※ 14 August 2022
Cite • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
WEPA40 The L-CAPE Project at FNAL controls, operation, linac, network 719
 
  • M. Jain, V.C. Amatya, G.U. Panapitiya, J.F. Strube
    PNNL, Richland, Washington, USA
  • B.F. Harrison, K.J. Hazelwood, W. Pellico, B.A. Schupbach, K. Seiya, J.M. St. John
    Fermilab, Batavia, Illinois, USA
 
  The controls system at FNAL records data asynchronously from several thousand Linac devices at their respective cadences, ranging from 15Hz down to once per minute. In case of downtimes, current operations are mostly reactive, investigating the cause of an outage and labeling it after the fact. However, as one of the most upstream systems at the FNAL accelerator complex, the Linac’s foreknowledge of an impending downtime as well as its duration could prompt downstream systems to go into standby, potentially leading to energy savings. The goals of the Linac Condition Anomaly Prediction of Emergence (L-CAPE) project that started in late 2020 are (1) to apply data-analytic methods to improve the information that is available to operators in the control room, and (2) to use machine learning to automate the labeling of outage types as they occur and discover patterns in the data that could lead to the prediction of outages. We present an overview of the challenges in dealing with time-series data from 2000+ devices, our approach to developing an ML-based automated outage labeling system, and the status of augmenting operations by identifying the most likely devices predicting an outage.  
poster icon Poster WEPA40 [1.870 MB]  
DOI • reference for this paper ※ doi:10.18429/JACoW-NAPAC2022-WEPA40  
About • Received ※ 03 August 2022 — Revised ※ 12 August 2022 — Accepted ※ 17 August 2022 — Issue date ※ 31 August 2022
Cite • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)  
 
THYE3 Superconducting Undulators and Cryomodules for X-ray Free-Electron Lasers FEL, undulator, electron, quadrupole 870
 
  • D.C. Nguyen, G.J. Bouchard, B.M. Dunham, G.L. Gassner, Z. Huang, E.M. Kraft, P. Krejcik, M.A. Montironi, H.-D. Nuhn, T.O. Raubenheimer, Z.R. Wolf, Z. Zhang
    SLAC, Menlo Park, California, USA
  • J.M. Byrd, J.D. Fuerst, E. Gluskin, Y. Ivanyushenkov, M. Kasa, E.R. Moog, M.F. Qian, Y. Shiroyanagi
    ANL, Lemont, Illinois, USA
 
  Funding: Work supported by the US DOE Office of Science, Basic Energy Sciences, Office of Accelerator and Detector Research (Manager: Dr. Eliane Lessner).
We present connectable designs of superconducting undulators (SCU) and cryomodules (CM) based on previous SCU and CM designs at Argonne National Lab. The new SCU and CM designs will allow us to connect one CM to the next to form a contiguous line of SCUs with no breaks between the cryomodules. The SCU design will have correctors and phase shifters integrated into the main SCU magnet core, as well as external corrector magnets for trajectory corrections. There will also be a cryogenic magnetic quadrupole and a cold RF beam position monitor (BPM) integrated in the SCU CM. In addition to providing the usual FODO transverse focusing, the quadrupole and BPM will be used for the beam-based alignment technique that is critical for X-ray FEL operation. In this paper, we will present the conceptual design of the new SCU CM as well as results of FEL simulations using the SCUs as afterburners for the LCLS hard X-ray undulators.
 
slides icon Slides THYE3 [2.657 MB]  
DOI • reference for this paper ※ doi:10.18429/JACoW-NAPAC2022-THYE3  
About • Received ※ 02 August 2022 — Revised ※ 07 August 2022 — Accepted ※ 08 August 2022 — Issue date ※ 16 August 2022
Cite • reference for this paper using ※ BibTeX, ※ LaTeX, ※ Text/Word, ※ RIS, ※ EndNote (xml)